Detailed analysis
General information
“Overall quality” is a quick reading of the tank’s general condition: the higher the score, the closer all measured parameters are to the recommended target values. It is not a “judgment” of the tank, but a guide for setting priorities: an average score may hide 1 or 2 really important parameters that should be corrected first.
The “By major categories” chart shows where the biggest gap lies: basic values (salinity, KH), major elements (Ca, Mg…), nutrients (NO3, PO4), trace elements (I, Fe, Mn…), and pollutants. The idea is simple: you immediately spot the category or categories pulling the score down, then go to the detailed table to see exactly which elements are in “Warning” or “Needs correction”.
Method tip: always start by stabilizing salinity and KH (these are the foundations), then adjust the major elements (Calcium / Magnesium), and only then the nutrients and trace elements. And above all: correct gradually. Several small, well-controlled adjustments are better than one big correction all at once.
Overall quality
By major categories
These synthetic indicators give you an overall view of your aquarium’s chemical balance, beyond the individual values. Rather than analyzing each element separately, they group several related parameters together to assess overall consistency.
The “Macro / Halogens Average” corresponds to a grouping of major and halogen elements (such as calcium, magnesium, potassium, iodine, bromine, etc.). These elements play a central role in coral growth, biological stability, and the overall proper functioning of the tank.
The “Organic Factors Average” groups together the parameters related to nutrients and organic compounds (nitrates, phosphates, organic carbon, etc.). It helps assess whether the organic load is balanced, too high (risk of algae, cyanobacteria), or too low (risk of deficiencies and starving corals).
Ratios are expressed as percentages, with a target set at 100%. A ratio close to 100% indicates that, overall, the elements in the group are aligned with their target values. A ratio below 100% suggests an average deficiency, while a ratio above it may indicate an overall excess.
These averages do not replace a detailed element-by-element analysis, but they are ideal for quickly detecting an overall drift and tracking your tank’s evolution over time. Use them as trend indicators: if an average remains far from 100% over time, it is recommended to examine the relevant elements in the detailed table.
Macro / Halogens Average
Organic Factors Average
This panel gives you an immediate view of the parameters that require special attention. It highlights only the values that are outside the target zone, so you can focus on what matters most.
A “Needs correction” status indicates a significant deviation that should be treated as a priority. A “Warning” status indicates a more moderate deviation to watch and adjust gradually.
Filters let you display only “Needs correction” parameters, only those in “Warning”, or the full set. The detailed table below updates automatically.
Each element is clickable: one click scrolls to its row in the table, giving you quick access to the value, the visual gauge and the actions.
The detailed table groups together all the chemical elements measured in your aquarium, classified by major families to make it easier to read. Each row corresponds to a specific element (calcium, magnesium, iodine, nitrate, etc.), with all the information needed to understand its current situation.
The “Measurement” column shows the value detected in the analysis. If the element is marked as ND (not detected), it means it is below the laboratory’s detection limit. Right next to it, the visual deviation gauge lets you interpret the value at a glance: target zone (green), warning zone or needs-correction zone depending on the gap from the target.
The “Status” column summarizes this information with a clear label (OK, Warning, Needs correction) to help you prioritize actions.
The “Action” button opens a correction recommendation tailored to your volume and the observed deviation, while the “Info” button gives a more scientific explanation of the element’s role in the aquarium.
Use this table as your main decision tool: start with the “Needs correction” rows, then handle the “Warning” ones, and leave the OK parameters under simple monitoring.
Basic parameters
| Element | Measurement | Visual deviation | Status | Actions |
|---|---|---|---|---|
| DKH Carbonate hardness |
7.2 dKH
Ideal value :
7.5
|
|
OK | |
| EC Conductivity |
56.7 mS/cm
Ideal value :
53
|
|
OK | |
| pH pH |
7.96 pH
Ideal value :
8.15
|
|
OK | |
| PSU Salinity |
37.7 PSU
Ideal value :
35
|
|
Warning |
Base
DKH
Carbonate hardness
OK
Measured
7.2 dKH
→
Target
7.5
dKH
EC
Conductivity
OK
Measured
56.7 mS/cm
→
Target
53
mS/cm
pH
pH
OK
Measured
7.96 pH
→
Target
8.15
pH
PSU
Salinity
Warning
Measured
37.7 PSU
→
Target
35
PSU
Major elements
| Element | Measurement | Visual deviation | Status | Actions |
|---|---|---|---|---|
| B Boron |
4.24 mg/L
Ideal value :
4.65
|
|
OK | |
| Br Bromine |
102 mg/L
Ideal value :
68
|
|
Needs correction | |
| Ca Calcium |
437 mg/L
Ideal value :
420
|
|
OK | |
| Cl Chloride |
20722 mg/L
Ideal value :
19500
|
|
Warning | |
| F Fluoride |
1.06 mg/L
Ideal value :
1.3
|
|
OK | |
| Mg Magnesium |
1469 mg/L
Ideal value :
1350
|
|
Warning | |
| K Potassium |
510 mg/L
Ideal value :
400
|
|
Needs correction | |
| Na Sodium |
12058 mg/L
Ideal value :
10700
|
|
Warning | |
| Sr Strontium |
4.1 mg/L
Ideal value :
8
|
|
Warning | |
| SO4 Sulfate |
2750 mg/L
Ideal value :
2700
|
|
OK | |
| S Sulfur |
918 mg/L
Ideal value :
900
|
|
OK |
Major
B
Boron
OK
Measured
4.24 mg/L
→
Target
4.65
mg/L
Br
Bromine
Needs correction
Measured
102 mg/L
→
Target
68
mg/L
Ca
Calcium
OK
Measured
437 mg/L
→
Target
420
mg/L
Cl
Chloride
Warning
Measured
20722 mg/L
→
Target
19500
mg/L
F
Fluoride
OK
Measured
1.06 mg/L
→
Target
1.3
mg/L
Mg
Magnesium
Warning
Measured
1469 mg/L
→
Target
1350
mg/L
K
Potassium
Needs correction
Measured
510 mg/L
→
Target
400
mg/L
Na
Sodium
Warning
Measured
12058 mg/L
→
Target
10700
mg/L
Sr
Strontium
Warning
Measured
4.1 mg/L
→
Target
8
mg/L
SO4
Sulfate
OK
Measured
2750 mg/L
→
Target
2700
mg/L
S
Sulfur
OK
Measured
918 mg/L
→
Target
900
mg/L
Nutrients
| Element | Measurement | Visual deviation | Status | Actions |
|---|---|---|---|---|
| NO3 Nitrate |
0.7 mg/L
Ideal value :
5.5
|
|
Needs correction | |
| NO2 Nitrite |
0.02 mg/L
Ideal value :
0.05
|
|
OK | |
| PO4 Phosphate |
0.055 mg/L
Ideal value :
0.06
|
|
OK | |
| P Phosphorus |
18 µg/L
Ideal value :
33
|
|
OK | |
| SiO2 Silicates |
0.77 mg/L
Ideal value :
0.44
|
|
Needs correction |
Nutrients
NO3
Nitrate
Needs correction
Measured
0.7 mg/L
→
Target
5.5
mg/L
NO2
Nitrite
OK
Measured
0.02 mg/L
→
Target
0.05
mg/L
PO4
Phosphate
OK
Measured
0.055 mg/L
→
Target
0.06
mg/L
P
Phosphorus
OK
Measured
18 µg/L
→
Target
33
µg/L
SiO2
Silicates
Needs correction
Measured
0.77 mg/L
→
Target
0.44
mg/L
Trace elements
| Element | Measurement | Visual deviation | Status | Actions |
|---|---|---|---|---|
| Ba Barium |
94.4 µg/L
Ideal value :
12.5
|
|
Needs correction | |
| Cr Chromium |
0 µg/L
Ideal value :
0.5
|
|
N/A | |
| Co Cobalt |
0.95 µg/L
Ideal value :
0.25
|
|
OK | |
| Cu Copper |
1.48 µg/L
Ideal value :
4
|
|
Needs correction | |
| I Iodine |
52 µg/L
Ideal value :
67.5
|
|
Warning | |
| Fe Iron |
1.89 µg/L
Ideal value :
1.275
|
|
OK | |
| Li Lithium |
213 µg/L
Ideal value :
265
|
|
OK | |
| Mn Manganese |
0.32 µg/L
Ideal value :
0.25
|
|
OK | |
| Mo Molybdenum |
15.4 µg/L
Ideal value :
15
|
|
OK | |
| Ni Nickel |
4.42 µg/L
Ideal value :
3
|
|
OK | |
| Se Selenium |
0 µg/L
Ideal value :
0.5
|
|
N/A | |
| Si Silicon |
360 µg/L
Ideal value :
150
|
|
Needs correction | |
| V Vanadium |
1.74 µg/L
Ideal value :
3
|
|
OK | |
| Zn Zinc |
19.3 µg/L
Ideal value :
5.5
|
|
Needs correction |
Minor
Ba
Barium
Needs correction
Measured
94.4 µg/L
→
Target
12.5
µg/L
Cr
Chromium
N/A
Measured
0 µg/L
→
Target
0.5
µg/L
Co
Cobalt
OK
Measured
0.95 µg/L
→
Target
0.25
µg/L
Cu
Copper
Needs correction
Measured
1.48 µg/L
→
Target
4
µg/L
I
Iodine
Warning
Measured
52 µg/L
→
Target
67.5
µg/L
Fe
Iron
OK
Measured
1.89 µg/L
→
Target
1.275
µg/L
Li
Lithium
OK
Measured
213 µg/L
→
Target
265
µg/L
Mn
Manganese
OK
Measured
0.32 µg/L
→
Target
0.25
µg/L
Mo
Molybdenum
OK
Measured
15.4 µg/L
→
Target
15
µg/L
Ni
Nickel
OK
Measured
4.42 µg/L
→
Target
3
µg/L
Se
Selenium
N/A
Measured
0 µg/L
→
Target
0.5
µg/L
Si
Silicon
Needs correction
Measured
360 µg/L
→
Target
150
µg/L
V
Vanadium
OK
Measured
1.74 µg/L
→
Target
3
µg/L
Zn
Zinc
Needs correction
Measured
19.3 µg/L
→
Target
5.5
µg/L
Pollutants
| Element | Measurement | Visual deviation | Status | Actions |
|---|---|---|---|---|
| Al Aluminum |
10.9 µg/L
Ideal value :
17.5
|
|
OK | |
| Sb Antimony |
0 µg/L
Ideal value :
|
|
N/A | |
| As Arsenic |
0 µg/L
Ideal value :
|
|
N/A | |
| Cd Cadmium |
0 µg/L
Ideal value :
|
|
N/A | |
| Cs Cesium |
0 µg/L
Ideal value :
|
|
N/A | |
| Ga Gallium |
0 µg/L
Ideal value :
|
|
N/A | |
| La Lanthanum |
0 µg/L
Ideal value :
2
|
|
N/A | |
| Pb Lead |
0 µg/L
Ideal value :
|
|
N/A | |
| Hg Mercury |
0 µg/L
Ideal value :
|
|
N/A | |
| Nd Neodymium |
0 µg/L
Ideal value :
|
|
N/A | |
| Ag Silver |
0 µg/L
Ideal value :
|
|
N/A | |
| Te Tellurium |
0 µg/L
Ideal value :
|
|
N/A | |
| Tl Thallium |
0 µg/L
Ideal value :
|
|
N/A | |
| Sn Tin |
0 µg/L
Ideal value :
5
|
|
N/A | |
| Ti Titanium |
0 µg/L
Ideal value :
|
|
N/A | |
| W Tungsten |
0 µg/L
Ideal value :
|
|
N/A | |
| U Uranium |
0 µg/L
Ideal value :
|
|
N/A | |
| Zr Zirconium |
0 µg/L
Ideal value :
|
|
N/A |